With the winter season quickly approaching, central heating for your home becomes a priority. In order to keep your home warm, all components of your central heating system must be in proper working order. However, there are some typical faults with the system that tend to happen at the worst possible time. One such common problem is frost damage, which can damage and sometimes destroy boilers and pipes.
In previous years, the central heating system was designed with the frost thermostat located near the boiler. Its job was to start the boiler when the air temperature dropped and stop the boiler when the air temperature reached an acceptable level. If the thermostat detected excessive heat escaping from the boiler or surrounding pipes it quickly turned off the system, in order to conserve energy and prevent excessive heating of the home.
In recent years, the boiler and nearby pipes have been insulated much better (thus effectively saving energy) that the frost thermostat can no longer effectively determine when the air temperature has reached the requested degree. This can prove to be problematic, as it may lead to overheating.
Installing a pipe thermostat can solve this problem. A pipe thermostat is typically placed on the outside of the boiler return pipe, measuring the temperature of the pipe (assuming copper pipes are good heat conductive materials). Its purpose is to turn off the boiler before overheating occurs. There are several new products that contain both a frost thermostat and low limit pipe thermostat, providing standard room temperature setting capabilities along with frost protection capabilities.
Set up and installation of the thermostats is easy and user friendly. Directions for installation and wiring arrive along with the product, all in one kit. Frost thermostats are commonly set to 5C and pipe thermostats are usually set to 25C. If you have additional exposed pipes (e.g in the garage), extra thermostats can be bought to secure your central heating system completely.
Another heating regulation solution is the fully programmable room thermostat. Such devices are normally installed inside the living area (typically the hallway or the living room) to take a typical measure of the room temperature. Modern designs can be set to alter the temperature several times throughout the course of a day. More recent kits have wireless models that operate via a radio signal from the thermostat to the boiler. Such RF (Radio Frequency) thermostats are easy to install as they do not require wiring, but rather use a secure radio frequency to relay their reading to the boiler control unit.
However, it is important to note that a thermostat is not the only way to heat your home in the most effective way. Adjusting the zones where heat is distributed can be a big energy saver. Focus heat where most time is spent and allow rooms that are not frequently used to remain cooler. This simple change will impact the efficiency of your central heating system greatly and help you reduce your heating bills. - 16477
In previous years, the central heating system was designed with the frost thermostat located near the boiler. Its job was to start the boiler when the air temperature dropped and stop the boiler when the air temperature reached an acceptable level. If the thermostat detected excessive heat escaping from the boiler or surrounding pipes it quickly turned off the system, in order to conserve energy and prevent excessive heating of the home.
In recent years, the boiler and nearby pipes have been insulated much better (thus effectively saving energy) that the frost thermostat can no longer effectively determine when the air temperature has reached the requested degree. This can prove to be problematic, as it may lead to overheating.
Installing a pipe thermostat can solve this problem. A pipe thermostat is typically placed on the outside of the boiler return pipe, measuring the temperature of the pipe (assuming copper pipes are good heat conductive materials). Its purpose is to turn off the boiler before overheating occurs. There are several new products that contain both a frost thermostat and low limit pipe thermostat, providing standard room temperature setting capabilities along with frost protection capabilities.
Set up and installation of the thermostats is easy and user friendly. Directions for installation and wiring arrive along with the product, all in one kit. Frost thermostats are commonly set to 5C and pipe thermostats are usually set to 25C. If you have additional exposed pipes (e.g in the garage), extra thermostats can be bought to secure your central heating system completely.
Another heating regulation solution is the fully programmable room thermostat. Such devices are normally installed inside the living area (typically the hallway or the living room) to take a typical measure of the room temperature. Modern designs can be set to alter the temperature several times throughout the course of a day. More recent kits have wireless models that operate via a radio signal from the thermostat to the boiler. Such RF (Radio Frequency) thermostats are easy to install as they do not require wiring, but rather use a secure radio frequency to relay their reading to the boiler control unit.
However, it is important to note that a thermostat is not the only way to heat your home in the most effective way. Adjusting the zones where heat is distributed can be a big energy saver. Focus heat where most time is spent and allow rooms that are not frequently used to remain cooler. This simple change will impact the efficiency of your central heating system greatly and help you reduce your heating bills. - 16477
About the Author:
Tal Potishman, editor of Heating Central, writes articles about central heating, combi boilers, Golders Green plumbers, underfloor heating and solar thermal. He specializes in helping save money by advising on efficient heating.
No comments:
Post a Comment